![]() ![]() #zero_reference_position: 175,175 #for use with stock z endstopįade_start : 0.6 fade_end : 10.0 probe_count : 5, 5 # Values should be odd, so one point is directly at bed center #zero_reference_position: 150,150 #for use with stock z endstop #zero_reference_position: 125,125 #for use with stock z endstop The Switchwire stock configs already include this.You can copy & paste this into your printer.cfg, making sure to uncomment the appropriate mesh_min and mesh_max for your bed size. If you have an older install, and need to use RELATIVE_REFERENCE_INDEX, you may find instructions for that hereīecause your mesh can change at different bed, chamber, and frame temperatures, it is generally recommended to generate a mesh before every print rather than using saved meshes.Īll of the configuration options and explanations can be found in the Klipper docs. These instructions assume that you are using a reasonably up to date Klipper, which supports ZERO_REFERENCE_POSITION. This often requires a bed mesh to compensate. The extrusions with linear rails will actually bend slightly when heated due to differing rates of thermal expansion. While the thick beds themselves are usually quite flat, your gantry and frame will expand and warp a bit with chamber heat. Larger printers are also likely to need a bed mesh, but for different reasons. To run a mesh, you should place BED_MESH_CALIBRATE in your PRINT_START macro after G28 (and after bed heating). ![]() It is important to check that your probe is correctly calibrated using PROBE_CALIBRATE. Note that unlike other Voron models, the Switchwire uses the probe as a virtual endstop, and thus should NOT use relative_reference_index. However, if you do wish to fine tune it, detailed information can be found in the Klipper docs. The mesh settings in the stock configs are usually fine. It’s more difficult to get a good reading, but easier to interpret the result.ĭue to the the use of a thinner bed on the switchwire, a bed mesh is usually needed. This app shows a single frequency rather than a graph.Both: Gates Carbon Drive (use the “motorcycle” option).Move your gantry down at least a few centimeters and then back up again.Pluck, measure, and adjust, same as above.Move the gantry upwards until the fixed side of the belt is 150mm from the Z idler centers.Z Belts (Voron V2)Ī good starting point is 140hz. This should be a good starting point without stretching your belts too tight. Re-check your tensions.ġ10hz equals roughly 2lb of belt tension here, which is on the lower end of the range. Move your X extrusion back at least a few centimeters and then back again.Go back and forth adjusting each until they are equal. Tightening one will also tighten the other. The A/B belt tensions can affect each other.Adjust the tensions until the lowest frequency in your plot registers approximately 110Hz.Pluck the 150mm section of belt and measure the frequency with one of the apps listed below.Move your X extrusion forwards until the X/Y idler centers are 150mm from the front idler centers. ![]() Belt Tensionīelts that are too tight (or too loose) can cause mechanical issues, premature wear and print quality issues. V2: See the V2 gantry squaring instructions.Īll Printers: See Nero’s gantry racking video. Which ones do you use, and which ones have helped you more than you’ve expected them to?ĭid I help you find the best Android app for musicians out there? Tell me what you think in the comments section below!.Tuning steps and processes after everything is working. I’ve personally used most of the apps on this list, and I’m still using a few of them to this day. However, with the comfort of having all these functions and features in your pocket, it’s sure to be a good value for your hard-earned money, especially if it helps you achieve what you want to achieve. Most of the apps can be downloaded for free, although others will require you to shell out a few bucks before you can unlock all the features, and a few require you to purchase them. Amateurs and professionals alike can all use these apps to their benefit. The apps mentioned above are guaranteed to be useful for any musician with an Android phone. ![]() But, there are many alternatives, such as Band Lab and FL Studio, for your Android phones. No, GarageBand isn’t offered on Android devices. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |